Designing a PCB with the DEX PCB Designer > Designs > From Concept to Creation: Mastering PCB Design > PCB Layout and Design > Routing: techniques, guidelines, and best practices

Routing, the process of creating electronic connections between components on a printed circuit board (PCB), is a complex and critical aspect of the PCB design process. Proper routing contributes significantly to the overall performance and reliability of the final product. Here are techniques, guidelines, and best practices that should be considered during the PCB routing stage:

Pre-Routing Preparation

•Understand Circuit Requirements: Analyze your circuit’s specific needs, including signal integrity, impedance control, current-carrying capacity, and EMC (Electromagnetic Compatibility) requirements.

•Define Design Rules: Set up design rules in your PCB design software. This step involves defining clearances, minimum trace widths, via parameters, and other specifications based on your PCB's operational requirements and manufacturing capabilities.

Critical Signals Routing

•Route Critical Traces First: High-speed, RF (Radio Frequency), and sensitive analog traces should be routed first to ensure optimal layout and minimal interference. These may require specific impedance, length matching, or isolation.

•Consider Signal Paths: Minimize the length of high-speed signal paths to reduce signal degradation. Avoid sharp bends or right-angle turns that can cause impedance changes and signal reflections.

Power Delivery Network (PDN) Design

•Plan Power and Ground Distribution: Use wide traces for power and ground or dedicated planes in multi-layer PCBs. Ensure good connectivity and solid grounding, especially for high-current or noise-sensitive applications.

•Utilize Decoupling Capacitors: Place them close to the power pins of active components to stabilize power supply and filter high-frequency noise.

Electromagnetic Compatibility

•Minimize EMI Sources: Route traces to avoid creating antennas that radiate or pick up interference. This precaution involves considering trace length, routing paths, and layer transitions.

•Use Ground Planes: They shield signals from interference, provide a reference plane for signals, and help in heat dissipation. Make sure the ground plane is as continuous as possible, with no gaps or splits under sensitive signals.

Analog and Digital Signal Separation

•Maintain Separate Regions: If your PCB includes both analog and digital components, keep their traces and components in separate regions to prevent digital noise from contaminating sensitive analog signals.

•Avoid Common Return Paths: Shared return paths can lead to ground loops and unwanted interference. Ensure that digital and analog ground planes are connected in one point, usually at the power source, to avoid creating ground loops.

Impedance Control and Matching

•Maintain Consistent Impedance: For high-speed signals or RF circuits, use controlled impedance traces to prevent signal reflection and ensure signal integrity.

•Implement Length Matching: For differential signals or data lines running in parallel (like in DDR), traces should be length-matched to prevent timing issues and ensure synchronous communication.

Thermal Management

•Consider Heat Dissipation: Use wider traces, thermal vias, and heat sinks for components that generate significant heat to prevent hotspots and ensure component longevity.

•Assess Thermal Reliefs: These are essential for improving solderability on heavy components but can reduce trace current-carrying capacity and create thermal imbalance. Balance these needs based on your application.

Effective Use of Vias

•Minimize Via Transitions: Each via introduces additional inductance and potential signal loss. While vias are sometimes necessary, especially in multi-layer boards, their overuse can degrade signal quality.

•Understand Via Types: Different via types (through-hole, blind, buried) have different properties and use cases. Choose appropriately based on PCB stack-up and signal requirements.

Design for Manufacturability (DFM) and Testability

•Adhere to Manufacturing Limits: Ensure that trace widths, via sizes, and clearances meet the minimum requirements set by your PCB manufacturer.

•Include Test Points: Accessible test points for important signals and power rails are essential for PCB testing and troubleshooting.

Iterative Testing and Improvement

•Conduct Post-Layout Simulation: Use software tools to simulate the behavior of critical signals, identifying potential issues like crosstalk or signal loss.

•Prototype and Test: Building a prototype to perform physical testing is crucial. Real-world performance can differ from simulations, and testing helps catch issues before mass production.

Conclusion

Effective routing is an intricate task that plays a pivotal role in PCB design, directly impacting the functionality, reliability, and manufacturability of the final product. By following these established guidelines and best practices, designers can tackle complex routing challenges, ensuring robust performance of the electronics products while avoiding common pitfalls that lead to operational failures, redesigns, or product recalls.